[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x51af8014] [ 0.000000] Linux version 6.1.63 (acidslide@acidslideubuntu2204) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24715-1ea7824685) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Tue Dec 26 01:47:13 2023 [ 0.000000] Machine model: Linksys MR7350 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x00000000407fffff] [ 0.000000] node 0: [mem 0x0000000040800000-0x000000004a0fffff] [ 0.000000] node 0: [mem 0x000000004a100000-0x000000004d4fffff] [ 0.000000] node 0: [mem 0x000000004d500000-0x000000005fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 17 pages/cpu s31080 r8192 d30360 u69632 [ 0.000000] pcpu-alloc: s31080 r8192 d30360 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129024 [ 0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=rootfs root=mtd:squashfs rootwait ubi.block=0,rootfs root=/dev/ubiblock0_0 [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 437324K/524288K available (10304K kernel code, 858K rwdata, 2180K rodata, 1408K init, 273K bss, 86964K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479] [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 and mmio timer(s) running at 24.00MHz (virt/virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000089] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000102] pid_max: default: 32768 minimum: 301 [ 0.000573] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.000586] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.002446] cblist_init_generic: Setting adjustable number of callback queues. [ 0.002454] cblist_init_generic: Setting shift to 2 and lim to 1. [ 0.002658] rcu: Hierarchical SRCU implementation. [ 0.002662] rcu: Max phase no-delay instances is 1000. [ 0.003326] smp: Bringing up secondary CPUs ... [ 0.003975] Detected VIPT I-cache on CPU1 [ 0.004105] CPU1: Booted secondary processor 0x0000000001 [0x51af8014] [ 0.004760] Detected VIPT I-cache on CPU2 [ 0.004855] CPU2: Booted secondary processor 0x0000000002 [0x51af8014] [ 0.005473] Detected VIPT I-cache on CPU3 [ 0.005562] CPU3: Booted secondary processor 0x0000000003 [0x51af8014] [ 0.005630] smp: Brought up 1 node, 4 CPUs [ 0.005638] SMP: Total of 4 processors activated. [ 0.005643] CPU features: detected: 32-bit EL0 Support [ 0.005647] CPU features: detected: CRC32 instructions [ 0.005711] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.005717] CPU: All CPU(s) started at EL1 [ 0.005720] alternatives: applying system-wide alternatives [ 0.013184] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.013212] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.013440] pinctrl core: initialized pinctrl subsystem [ 0.014574] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.015154] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.015194] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.015229] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.015594] thermal_sys: Registered thermal governor 'step_wise' [ 0.015800] cpuidle: using governor menu [ 0.016125] ASID allocator initialised with 65536 entries [ 0.022612] gpio-493 (usb-power-gpio): hogged as output/high [ 0.071952] SCSI subsystem initialized [ 0.072144] usbcore: registered new interface driver usbfs [ 0.072182] usbcore: registered new interface driver hub [ 0.072216] usbcore: registered new device driver usb [ 0.072524] qcom_scm: convention: smc arm 64 [ 0.074627] s2: Bringing 0uV into 725000-725000uV [ 0.074694] clocksource: Switched to clocksource arch_sys_counter [ 0.075818] NET: Registered PF_INET protocol family [ 0.075985] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.076843] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.076863] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.076881] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.076933] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.077076] TCP: Hash tables configured (established 4096 bind 4096) [ 0.077176] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.077202] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.077401] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.077438] PCI: CLS 0 bytes, default 64 [ 0.078723] workingset: timestamp_bits=46 max_order=17 bucket_order=0 [ 0.083475] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.083487] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.086323] qcom-qmp-usb-phy 78000.ssphy: supply vdda-phy not found, using dummy regulator [ 0.086477] qcom-qmp-usb-phy 78000.ssphy: supply vdda-pll not found, using dummy regulator [ 0.088113] qcom-qusb2-phy 79000.qusb: supply vdd not found, using dummy regulator [ 0.088263] qcom-qusb2-phy 79000.qusb: supply vdda-pll not found, using dummy regulator [ 0.088304] qcom-qusb2-phy 79000.qusb: supply vdda-phy-dpdm not found, using dummy regulator [ 0.088464] qcom-qusb2-phy 79000.qusb: Registered Qcom-QUSB2 phy [ 0.091702] bam-dma-engine 704000.dma-controller: num-channels unspecified in dt [ 0.091718] bam-dma-engine 704000.dma-controller: num-ees unspecified in dt [ 0.096709] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.097371] msm_serial 78b1000.serial: msm_serial: detected port #0 [ 0.097424] msm_serial 78b1000.serial: uartclk = 1843200 [ 0.097514] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 22, base_baud = 115200) is a MSM [ 0.097543] msm_serial: console setup on port #0 [ 0.764047] printk: console [ttyMSM0] enabled [ 0.769213] msm_serial: driver initialized [ 0.778128] loop: module loaded [ 0.779482] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa [ 0.780089] nand: Macronix MX30UF2G18AC [ 0.786698] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.790261] Block protection check failed [ 0.813457] i2c_dev: i2c /dev entries driver [ 0.819537] sdhci: Secure Digital Host Controller Interface driver [ 0.819580] sdhci: Copyright(c) Pierre Ossman [ 0.824614] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.831494] remoteproc remoteproc0: releasing cd00000.remoteproc [ 0.836915] NET: Registered PF_INET6 protocol family [ 0.841798] Segment Routing with IPv6 [ 0.845767] In-situ OAM (IOAM) with IPv6 [ 0.849341] NET: Registered PF_PACKET protocol family [ 0.853289] 8021q: 802.1Q VLAN Support v1.8 [ 0.882536] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa [ 0.882576] nand: Macronix MX30UF2G18AC [ 0.887979] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.891538] Block protection check failed [ 0.899503] 20 qcomsmem partitions found on MTD device qcom_nand.0 [ 0.903241] Creating 20 MTD partitions on "qcom_nand.0": [ 0.909335] 0x000000000000-0x000000180000 : "0:sbl1" [ 0.916534] 0x000000180000-0x000000280000 : "0:mibib" [ 0.921026] 0x000000280000-0x000000600000 : "0:qsee" [ 0.927725] 0x000000600000-0x000000680000 : "0:devcfg" [ 0.930563] 0x000000680000-0x000000700000 : "0:rpm" [ 0.935608] 0x000000700000-0x000000780000 : "0:cdt" [ 0.940321] 0x000000780000-0x000000800000 : "0:appsblenv" [ 0.945199] 0x000000800000-0x000000980000 : "0:appsbl" [ 0.951435] 0x000000980000-0x000000a00000 : "0:art" [ 0.955821] 0x000000a00000-0x000001300000 : "0:wififw" [ 0.966689] 0x000001300000-0x000001380000 : "0:ethphyfw" [ 0.967592] 0x000001380000-0x000001400000 : "u_env" [ 0.971955] 0x000001400000-0x000001440000 : "s_env" [ 0.976398] 0x000001440000-0x000001480000 : "devinfo" [ 0.981187] 0x000001480000-0x000001c80000 : "kernel" [ 0.992103] 0x000001c80000-0x000006680000 : "rootfs" [ 1.045919] mtd: setting mtd15 (rootfs) as root device [ 1.046208] mtdsplit: no squashfs found in "rootfs" [ 1.049996] 0x000006680000-0x000006e80000 : "alt_kernel" [ 1.061106] 0x000006e80000-0x00000b880000 : "alt_rootfs" [ 1.114872] 0x00000b880000-0x00000ba80000 : "sysdiag" [ 1.116899] 0x00000ba80000-0x00000fe80000 : "syscfg" [ 1.177197] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 799999 KHz, changing to: 864000 KHz [ 1.179026] remoteproc remoteproc0: cd00000.remoteproc is available [ 1.187561] ubi0: attaching mtd15 [ 1.512259] ubi0: scanning is finished [ 1.518438] ubi0: attached mtd15 (name "rootfs", size 74 MiB) [ 1.518480] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 1.523196] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 1.529967] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 1.536810] ubi0: good PEBs: 591, bad PEBs: 1, corrupted PEBs: 0 [ 1.543571] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 1.549832] ubi0: max/mean erase counter: 5/3, WL threshold: 4096, image sequence number: 1338432486 [ 1.556867] ubi0: available PEBs: 0, total reserved PEBs: 591, PEBs reserved for bad PEB handling: 39 [ 1.566167] ubi0: background thread "ubi_bgt0d" started, PID 434 [ 1.566785] block ubiblock0_0: created from ubi0:0(rootfs) [ 1.581591] UBI error: block: can't add 'rootfs' volume, err=-17 [ 1.590213] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 1.590892] Freeing unused kernel memory: 1408K [ 1.624812] Run /sbin/init as init process [ 1.624835] with arguments: [ 1.624838] /sbin/init [ 1.624842] with environment: [ 1.624845] HOME=/ [ 1.624849] TERM=linux [ 1.818610] init: Console is alive [ 1.818761] init: - watchdog - [ 2.454724] random: crng init done [ 2.895301] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.012055] ssdk_dt_parse_interrupt[916]:INFO:intr-gpio does not exist [ 3.068180] malibu_phy_api_ops_init[1934]:INFO:qca probe malibu phy driver succeeded! [ 3.515448] __adpt_hppe_uniphy_psgmii_mode_set[1161]:INFO:uniphy 0 psgmii channel selection [ 3.741229] regi_init[3603]:INFO:Initializing HPPE Done!! [ 3.741312] regi_init[3662]:INFO:qca-ssdk module init succeeded! [ 3.747734] EDMA ver 1 hw init [ 3.751889] EDMA HW Reset completed succesfully [ 3.754561] Num rings - TxDesc:1 (23-23) TxCmpl:1 (23-23) [ 3.758990] RxDesc:1 (15-15) RxFill:1 (7-7) [ 3.766462] GMAC2(ffffff8000bec900) Invalid MAC@ - using 9a:15:00:XX:XX:XX [ 3.769848] GMAC3(ffffff80032db900) Invalid MAC@ - using ce:e5:96:XX:XX:XX [ 3.776885] GMAC4(ffffff800405d900) Invalid MAC@ - using 96:22:a2:XX:XX:XX [ 3.783723] GMAC5(ffffff800405b900) Invalid MAC@ - using 06:26:b2:XX:XX:XX [ 3.790547] ********************************************************** [ 3.796060] * NSS Data Plane driver [ 3.802534] ********************************************************** [ 3.890125] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.890175] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 3.895410] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000000010010 [ 3.902102] xhci-hcd xhci-hcd.1.auto: irq 35, io mem 0x08a00000 [ 3.911577] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.917357] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 3.922899] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 3.930886] hub 1-0:1.0: USB hub found [ 3.937190] hub 1-0:1.0: 1 port detected [ 3.941161] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.945212] hub 2-0:1.0: USB hub found [ 3.952946] hub 2-0:1.0: 1 port detected [ 3.961486] usbcore: registered new interface driver usb-storage [ 3.962521] usbcore: registered new interface driver uas [ 3.966896] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.981362] init: - preinit - [ 4.476681] mtdblock: MTD device 'devinfo' is NAND, please consider using UBI block devices instead. [ 6.932920] mount_root: loading kmods from internal overlay [ 6.950534] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 6.952055] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 6.995653] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.070654] block: attempting to load /tmp/overlay/upper/etc/config/fstab [ 7.070790] block: unable to load configuration (fstab: Entry not found) [ 7.076552] block: attempting to load /tmp/overlay/etc/config/fstab [ 7.083279] block: unable to load configuration (fstab: Entry not found) [ 7.089339] block: attempting to load /etc/config/fstab [ 7.101943] block: unable to load configuration (fstab: Entry not found) [ 7.102050] block: no usable configuration [ 7.110772] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 7.112047] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 681 [ 7.142278] UBIFS (ubi0:1): recovery needed [ 7.253782] UBIFS (ubi0:1): recovery completed [ 7.253915] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 7.257162] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 7.265049] UBIFS (ubi0:1): FS size: 23363584 bytes (22 MiB, 184 LEBs), max 194 LEBs, journal size 1142784 bytes (1 MiB, 9 LEBs) [ 7.274957] UBIFS (ubi0:1): reserved for root: 1103519 bytes (1077 KiB) [ 7.286570] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID AE827D27-0664-44DF-B048-CEAC956DE553, small LPT model [ 7.293406] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 7.308197] block: extroot: not configured [ 7.313684] UBIFS (ubi0:1): un-mount UBI device 0 [ 7.315321] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops [ 7.323362] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 7.326251] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 684 [ 7.394091] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 7.394133] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 7.400928] UBIFS (ubi0:1): FS size: 23363584 bytes (22 MiB, 184 LEBs), max 194 LEBs, journal size 1142784 bytes (1 MiB, 9 LEBs) [ 7.410820] UBIFS (ubi0:1): reserved for root: 1103519 bytes (1077 KiB) [ 7.422441] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID AE827D27-0664-44DF-B048-CEAC956DE553, small LPT model [ 7.431159] mount_root: loading kmods from internal overlay [ 7.457409] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 7.458769] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 7.468856] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.493387] block: attempting to load /tmp/overlay/upper/etc/config/fstab [ 7.496412] block: extroot: not configured [ 7.500919] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 7.503391] block: extroot: not configured [ 7.511584] mount_root: switching to ubifs overlay [ 7.520154] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. [ 7.523759] urandom-seed: Seeding with /etc/urandom.seed [ 7.583334] procd: - early - [ 7.583469] procd: - watchdog - [ 7.683206] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.716442] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.752739] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.785840] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.819194] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.856090] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.890041] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.927190] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.962380] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 7.996176] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.032872] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.065590] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.100696] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.137941] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.141408] procd: - watchdog - [ 8.149798] procd: - ubus - [ 8.186655] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.231968] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.265161] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.298142] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.306600] procd: - init - [ 8.343422] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.382021] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.462898] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.511015] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.566314] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.603704] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.647068] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.682558] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.724918] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.741134] kmodloader: loading kernel modules from /etc/modules.d/* [ 8.761395] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.793099] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.811798] zram: Added device: zram0 [ 8.824509] tun: Universal TUN/TAP device driver, 1.6 [ 8.828309] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 8.832491] gre: GRE over IPv4 demultiplexor driver [ 8.838575] ip_gre: GRE over IPv4 tunneling driver [ 8.845102] ip6_gre: GRE over IPv6 tunneling driver [ 8.883460] GACT probability on [ 8.884404] Mirror/redirect action on [ 8.891161] u32 classifier [ 8.891191] input device check on [ 8.892760] Actions configured [ 8.903337] ntfs3: Max link count 4000 [ 8.903374] ntfs3: Enabled Linux POSIX ACLs support [ 8.909167] fuse: init (API version 7.37) [ 8.919656] Loading modules backported from Linux version v6.5-0-g2dde18cd1d8f [ 8.919696] Backport generated by backports.git v5.15.92-1-56-g5fb2ccb6b9e8 [ 8.961714] NET: Registered PF_QIPCRTR protocol family [ 8.965708] usbcore: registered new interface driver ums-alauda [ 8.966902] usbcore: registered new interface driver ums-cypress [ 8.972642] usbcore: registered new interface driver ums-datafab [ 8.979112] usbcore: registered new interface driver ums-freecom [ 8.984837] usbcore: registered new interface driver ums-isd200 [ 8.990962] usbcore: registered new interface driver ums-jumpshot [ 8.992563] urngd: v1.0.2 started. [ 9.002035] usbcore: registered new interface driver ums-karma [ 9.006373] usbcore: registered new interface driver ums-sddr09 [ 9.011942] usbcore: registered new interface driver ums-sddr55 [ 9.017962] usbcore: registered new interface driver ums-usbat [ 9.047420] xt_time: kernel timezone is -0000 [ 9.125216] PPP generic driver version 2.4.2 [ 9.126333] NET: Registered PF_PPPOX protocol family [ 9.137162] ath11k c000000.wifi: ipq6018 hw1.0 [ 9.137196] ath11k c000000.wifi: FW memory mode: 2 [ 9.140786] remoteproc remoteproc0: powering up cd00000.remoteproc [ 9.147233] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340 [ 10.032071] remoteproc remoteproc0: remote processor cd00000.remoteproc is now up [ 10.033200] ath11k c000000.wifi: qmi ignore invalid mem req type 3 [ 10.039180] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff [ 10.039276] batman_adv: B.A.T.M.A.N. advanced 2023.3-openwrt-3 (compatibility version 15) loaded [ 10.044626] ath11k c000000.wifi: fw_version 0x250a04b8 fw_build_timestamp 2021-12-20 07:20 fw_build_id WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1 [ 10.063493] kmodloader: done loading kernel modules from /etc/modules.d/* [ 10.495467] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 10.953834] zram0: detected capacity change from 0 to 438272 [ 10.961537] Adding 219132k swap on /dev/zram0. Priority:100 extents:1 across:219132k SSDsc [ 15.089241] br-lan: port 1(eth0) entered blocking state [ 15.089290] br-lan: port 1(eth0) entered disabled state [ 15.093574] device eth0 entered promiscuous mode [ 15.123942] br-lan: port 2(eth1) entered blocking state [ 15.123990] br-lan: port 2(eth1) entered disabled state [ 15.128304] device eth1 entered promiscuous mode [ 15.141827] br-lan: port 3(eth2) entered blocking state [ 15.141874] br-lan: port 3(eth2) entered disabled state [ 15.146192] device eth2 entered promiscuous mode [ 15.160878] br-lan: port 4(eth3) entered blocking state [ 15.160926] br-lan: port 4(eth3) entered disabled state [ 15.165231] device eth3 entered promiscuous mode [ 16.008142] cfg80211: Invalid regulatory domain detected: US [ 17.319686] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 19.316874] phy0-sta0: authenticate with XX:XX:XX:XX:XX:XX [ 19.420379] phy0-sta0: send auth to XX:XX:XX:XX:XX:XX (try 1/3) [ 19.421967] phy0-sta0: authenticated [ 19.434838] phy0-sta0: associate with XX:XX:XX:XX:XX:XX (try 1/3) [ 19.436280] phy0-sta0: RX AssocResp from XX:XX:XX:XX:XX:XX (capab=0x1011 status=0 aid=22) [ 19.441257] phy0-sta0: associated [ 19.615478] phy0-sta0: Limiting TX power to 30 (30 - 0) dBm as advertised by XX:XX:XX:XX:XX:XX [ 19.685480] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-sta0: link becomes ready [ 31.721454] phy0-sta0: deauthenticating from XX:XX:XX:XX:XX:XX by local choice (Reason: 3=DEAUTH_LEAVING) [ 32.399951] cfg80211: Invalid regulatory domain detected: US [ 36.697391] phy0-sta0: authenticate with XX:XX:XX:XX:XX:XX [ 36.704567] phy0-sta0: send auth to XX:XX:XX:XX:XX:XX (try 1/3) [ 36.706192] phy0-sta0: authenticated [ 36.714721] phy0-sta0: associate with XX:XX:XX:XX:XX:XX (try 1/3) [ 36.716107] phy0-sta0: RX AssocResp from XX:XX:XX:XX:XX:XX (capab=0x1011 status=0 aid=22) [ 36.721090] phy0-sta0: associated [ 36.885269] phy0-sta0: Limiting TX power to 30 (30 - 0) dBm as advertised by XX:XX:XX:XX:XX:XX [ 36.885493] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-sta0: link becomes ready [ 81.677100] nss-dp 3a001000.dp1 eth0: PHY Link up speed: 100 [ 81.677184] br-lan: port 1(eth0) entered blocking state [ 81.681839] br-lan: port 1(eth0) entered forwarding state [ 81.687157] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 82.716803] nss-dp 3a001000.dp1 eth0: PHY Link is down [ 82.717130] br-lan: port 1(eth0) entered disabled state [ 83.757580] nss-dp 3a001000.dp1 eth0: PHY Link up speed: 100 [ 83.757669] br-lan: port 1(eth0) entered blocking state [ 83.762317] br-lan: port 1(eth0) entered forwarding state [ 84.796365] nss-dp 3a001000.dp1 eth0: PHY Link is down [ 84.796652] br-lan: port 1(eth0) entered disabled state [ 86.877259] nss-dp 3a001000.dp1 eth0: PHY Link up speed: 100 [ 86.877342] br-lan: port 1(eth0) entered blocking state [ 86.881999] br-lan: port 1(eth0) entered forwarding state [ 87.916342] nss-dp 3a001000.dp1 eth0: PHY Link is down [ 87.916626] br-lan: port 1(eth0) entered disabled state [ 88.957554] nss-dp 3a001000.dp1 eth0: PHY Link up speed: 100 [ 88.957637] br-lan: port 1(eth0) entered blocking state [ 88.962291] br-lan: port 1(eth0) entered forwarding state [ 89.995951] nss-dp 3a001000.dp1 eth0: PHY Link is down [ 89.996246] br-lan: port 1(eth0) entered disabled state [ 92.077348] nss-dp 3a001000.dp1 eth0: PHY Link up speed: 100 [ 92.077432] br-lan: port 1(eth0) entered blocking state [ 92.082086] br-lan: port 1(eth0) entered forwarding state [ 93.115955] nss-dp 3a001000.dp1 eth0: PHY Link is down [ 93.116238] br-lan: port 1(eth0) entered disabled state [ 94.157446] nss-dp 3a001000.dp1 eth0: PHY Link up speed: 10 [ 94.157527] br-lan: port 1(eth0) entered blocking state [ 94.161836] br-lan: port 1(eth0) entered forwarding state