(AVM) EVA Revision: 1.1475 Version: 2475 (C) Copyright 2005 AVM Date: Nov 19 2012 Time: 11:18:01 (2) 2 0x0-0xB40D [FLASH:] MACRONIX Uniform-Flash 16MB 64 Bytes WriteBuffer [FLASH:](Eraseregion [0] 128 sectors a 128kB) [SYSTEM:] VR9 on 500MHz/250MHz/250MHz .Atheros 8030/35 detected Eva_AVM >....................................................................[ 0.000000] Linux version 5.10.176 (builder@buildhost) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r20134-5f15225c1e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Thu Apr 27 20:28:15 2023 [ 0.000000] SoC: xRX200 rev 1.2 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc) [ 0.000000] MIPS: machine is AVM FRITZ!Box 7360 SL [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Detected 1 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 14 pages/cpu s26800 r8192 d22352 u57344 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyLTQ0,115200 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 119448K/131072K available (6953K kernel code, 628K rwdata, 1108K rodata, 1276K init, 213K bss, 11624K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 500MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns [ 0.000013] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns [ 0.007999] Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880) [ 0.074076] pid_max: default: 32768 minimum: 301 [ 0.079000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.086196] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.098436] rcu: Hierarchical SRCU implementation. [ 0.103692] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.111828] smp: Bringing up secondary CPUs ... [ 0.117765] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.117781] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.117876] CPU1 revision is: 00019556 (MIPS 34Kc) [ 0.171514] Synchronize counters for CPU 1: done. [ 0.195827] smp: Brought up 1 node, 2 CPUs [ 0.207236] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.217019] futex hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.223959] pinctrl core: initialized pinctrl subsystem [ 0.231937] NET: Registered protocol family 16 [ 0.237239] thermal_sys: Registered thermal governor 'step_wise' [ 0.274648] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV [ 0.288443] pinctrl-xway 1e100b10.pinmux: Init done [ 0.303399] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28 [ 0.311408] pcie-xrx200 1d900000.pcie: failed to get the PCIe PHY [ 0.391529] usbcore: registered new interface driver usbfs [ 0.397180] usbcore: registered new interface driver hub [ 0.402654] usbcore: registered new device driver usb [ 0.417376] clocksource: Switched to clocksource MIPS [ 0.425472] NET: Registered protocol family 2 [ 0.430336] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.442695] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.451123] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.458806] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.465763] TCP: Hash tables configured (established 1024 bind 1024) [ 0.472445] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.478949] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.486300] NET: Registered protocol family 1 [ 0.490637] PCI: CLS 0 bytes, default 32 [ 0.495829] gptu: totally 6 16-bit timers/counters [ 0.500719] gptu: misc_register on minor 63 [ 0.504918] gptu: succeeded to request irq 126 [ 0.509398] gptu: succeeded to request irq 127 [ 0.513817] gptu: succeeded to request irq 128 [ 0.518451] gptu: succeeded to request irq 129 [ 0.522847] gptu: succeeded to request irq 130 [ 0.527506] gptu: succeeded to request irq 131 [ 0.532071] No VPEs reserved for AP/SP, not initialize VPE loader [ 0.532071] Pass maxvpes= argument as kernel argument [ 0.543474] No TCs reserved for AP/SP, not initializing RTLX. [ 0.543474] Pass maxtcs= argument as kernel argument [ 0.557137] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.572155] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.577897] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.589544] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.603301] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc [ 0.612382] printk: console [ttyLTQ0] enabled [ 0.612382] printk: console [ttyLTQ0] enabled [ 0.621045] printk: bootconsole [early0] disabled [ 0.621045] printk: bootconsole [early0] disabled [ 0.634064] lantiq nor flash device: 01000000 at 10000000 [ 0.638347] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.647771] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.652816] Amd/Fujitsu Extended Query version 1.3. [ 0.657900] number of CFI chips: 1 [ 0.661321] 4 fixed-partitions partitions found on MTD device ltq_nor [ 0.668926] Creating 4 MTD partitions on "ltq_nor": [ 0.672565] 0x000000000000-0x000000020000 : "urlader" [ 0.679947] 0x000000020000-0x000000f80000 : "firmware" [ 0.690757] 2 eva-fw partitions found on MTD device firmware [ 0.694982] 0x000000020000-0x0000002b5c54 : "kernel" [ 0.700065] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only [ 0.709710] 0x0000002c0100-0x000000f80000 : "rootfs" [ 0.713289] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 0.723970] mtd: setting mtd3 (rootfs) as root device [ 0.727774] 1 squashfs-split partitions found on MTD device rootfs [ 0.733831] 0x000000740000-0x000000f80000 : "rootfs_data" [ 0.740714] 0x000000f80000-0x000000fc0000 : "tffs (1)" [ 0.746007] 0x000000fc0000-0x000001000000 : "tffs (2)" [ 1.111890] gswip 1e108000.switch: dsa switch register failed: -517 [ 1.124675] hwmon hwmon0: temp1_input not attached to any thermal zone [ 1.136549] NET: Registered protocol family 10 [ 1.151919] Segment Routing with IPv6 [ 1.154292] NET: Registered protocol family 17 [ 1.158830] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.172231] 8021q: 802.1Q VLAN Support v1.8 [ 1.181937] pcie-xrx200 1d900000.pcie: failed to get the PCIe PHY [ 1.534581] gswip 1e108000.switch lan3 (uninitialized): PHY [1e108000.switch-mii:00] driver [Qualcomm Atheros AR8030] (irq=POLL) [ 1.548613] gswip 1e108000.switch lan4 (uninitialized): PHY [1e108000.switch-mii:01] driver [Qualcomm Atheros AR8030] (irq=POLL) [ 1.564299] gswip 1e108000.switch lan2 (uninitialized): PHY [1e108000.switch-mii:11] driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (irq=POLL) [ 1.581294] gswip 1e108000.switch lan1 (uninitialized): PHY [1e108000.switch-mii:13] driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (irq=POLL) [ 1.595459] DSA: tree 0 setup [ 1.597044] gswip 1e108000.switch: probed GSWIP version 21 mod 0 [ 1.725971] PCI host bridge /fpi@10000000/pcie@d900000 ranges: [ 1.730691] PCI host bridge to bus 0000:00 [ 1.734525] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff] [ 1.741423] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff] [ 1.748289] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 1.754991] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.763064] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge [ 1.780646] pci 0000:00:00.0: 0x806c5578 took 17150 usecs [ 1.784597] pci 0000:00:00.0: [1bef:0011] type 01 class 0x060400 [ 1.790780] pci 0000:00:00.0: PME# supported from D0 D3hot [ 1.799903] pci 0000:01:00.0: [168c:ff1c] type 00 class 0x020000 [ 1.804601] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit] [ 1.811554] pci 0000:01:00.0: supports D1 [ 1.815265] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 1.824369] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.829646] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 1.836192] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] [ 1.843035] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff 64bit] [ 1.850372] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.855225] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff] [ 1.862241] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1 [ 1.868704] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned [ 1.874914] pcieport 0000:00:00.0: enabling device (0000 -> 0002) [ 1.895478] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 1.903091] Freeing unused kernel memory: 1276K [ 1.906174] This architecture does not have kernel memory protection. [ 1.912704] Run /sbin/init as init process [ 2.816663] init: Console is alive [ 2.819314] init: - watchdog - [ 2.822114] init: Watchdog has previously reset the system [ 4.277892] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.480844] dwc2 1e101000.usb: supply vusb_d not found, using dummy regulator [ 4.487098] dwc2 1e101000.usb: supply vusb_a not found, using dummy regulator [ 4.595883] dwc2 1e101000.usb: DWC OTG Controller [ 4.599300] dwc2 1e101000.usb: new USB bus registered, assigned bus number 1 [ 4.606236] dwc2 1e101000.usb: irq 62, io mem 0x1e101000 [ 4.613062] hub 1-0:1.0: USB hub found [ 4.615608] hub 1-0:1.0: 1 port detected [ 4.621619] dwc2 1e106000.usb: supply vusb_d not found, using dummy regulator [ 4.627994] dwc2 1e106000.usb: supply vusb_a not found, using dummy regulator [ 4.737645] dwc2 1e106000.usb: DWC OTG Controller [ 4.740960] dwc2 1e106000.usb: new USB bus registered, assigned bus number 2 [ 4.748107] dwc2 1e106000.usb: irq 91, io mem 0x1e106000 [ 4.755026] hub 2-0:1.0: USB hub found [ 4.757972] hub 2-0:1.0: 1 port detected [ 4.766569] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.774522] init: - preinit - [ 5.287479] usb 2-1: new high-speed USB device number 2 using dwc2 [ 5.759531] random: procd: uninitialized urandom read (4 bytes read) [ 6.458541] random: jshn: uninitialized urandom read (4 bytes read) [ 6.851133] random: jshn: uninitialized urandom read (4 bytes read) [ 7.069030] random: jshn: uninitialized urandom read (4 bytes read) [ 7.177027] random: jshn: uninitialized urandom read (4 bytes read) [ 7.617247] gswip 1e108000.switch lan1: configuring for phy/internal link mode [ 7.623425] 8021q: adding VLAN 0 to HW filter on device lan1 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 12.175448] jffs2: notice: (603) jffs2_build_xattr_subsystem: complete building xattr subsystem, 86 of xdatum (48 unchecked, 37 orphan) and 115 of xref (33 dead, 4 orphan) found. [ 12.203538] mount_root: loading kmods from internal overlay [ 12.221433] kmodloader: failed to open /tmp/overlay/upper/lib/modules/5.10.176/drv_dsl_cpe_api.ko [ 12.516773] mount_root: failed to launch kmodloader from internal overlay [ 13.026320] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 13.039791] block: extroot: cannot find device with UUID c0a3305c-9ffb-47e3-bc3b-f55354cff508 [ 13.048799] mount_root: switching to jffs2 overlay [ 13.054942] overlayfs: upper fs does not support tmpfile. [ 13.124103] urandom-seed: Seeding with /etc/urandom.seed [ 13.298011] procd: - early - [ 13.299919] procd: - watchdog - [ 13.303045] procd: Watchdog has previously reset the system [ 14.092322] procd: - watchdog - [ 14.094961] procd: Watchdog has previously reset the system [ 14.103696] procd: - ubus - [ 14.384738] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.402846] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.410757] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.455737] procd: - init - Please press Enter to activate this console. [ 16.291392] random: jshn: uninitialized urandom read (4 bytes read) [ 16.323385] random: ubusd: uninitialized urandom read (4 bytes read) [ 17.581225] kmodloader: loading kernel modules from /etc/modules.d/* [ 18.343918] urngd: v1.0.2 started. [ 19.074319] random: crng init done [ 19.076346] random: 28 urandom warning(s) missed due to ratelimiting [ 19.109282] IFXOS, Version 1.7.1 (c) Copyright 2009, Lantiq Deutschland GmbH [ 19.126461] NET: Registered protocol family 8 [ 19.130102] NET: Registered protocol family 20 [ 19.790008] PPP generic driver version 2.4.2 [ 19.914187] SCSI subsystem initialized [ 19.994003] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG [ 20.031272] Loading modules backported from Linux version v5.15.92-0-ge515b9902f5f [ 20.047614] Backport generated by backports.git v5.15.92-1-0-gdfe0f60c [ 20.066061] Infineon Technologies DEU driver version 2.0.0 [ 20.077912] IFX DEU DES initialized (multiblock). [ 20.102279] IFX DEU AES initialized (multiblock). [ 20.106372] IFX DEU SHA1 initialized. [ 20.111391] IFX DEU MD5 initialized. [ 20.115297] IFX DEU SHA1_HMAC initialized. [ 20.119955] IFX DEU MD5_HMAC initialized. [ 20.195635] NET: Registered protocol family 24 [ 20.254167] usb-storage 2-1:1.0: USB Mass Storage device detected [ 20.269396] scsi host0: usb-storage 2-1:1.0 [ 20.275432] usbcore: registered new interface driver usb-storage [ 20.295333] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1 [ 20.300801] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned [ 20.306956] ath9k_pci_owl_loader 0000:01:00.0: enabling device (0000 -> 0002) [ 20.349874] ath9k_pci_owl_loader 0000:01:00.0: fixup device configuration [ 20.407206] pci 0000:01:00.0: [168c:002e] type 00 class 0x028000 [ 20.412633] pci 0000:01:00.0: reg 0x10: [mem 0x1c000000-0x1c00ffff 64bit] [ 20.419504] pci 0000:01:00.0: supports D1 [ 20.422663] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 20.434294] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff 64bit] [ 20.835306] usbcore: registered new interface driver uas [ 20.882418] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1 [ 20.887683] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned [ 20.893917] ath9k 0000:01:00.0: enabling device (0140 -> 0142) [ 20.926529] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xbc000000, irq=144 [ 20.936522] kmodloader: done loading kernel modules from /etc/modules.d/* [ 21.309600] scsi 0:0:0:0: Direct-Access Generic USB Flash Disk 7.76 PQ: 0 ANSI: 2 [ 21.340534] sd 0:0:0:0: [sda] 66203648 512-byte logical blocks: (33.9 GB/31.6 GiB) [ 21.357471] sd 0:0:0:0: [sda] Write Protect is off [ 21.362215] sd 0:0:0:0: [sda] No Caching mode page found [ 21.366175] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 21.749826] sda: sda1 [ 21.871262] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 46.298806] mount_root: loading kmods from internal overlay [ 46.395468] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 46.422482] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 47.218698] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 47.261639] gswip 1e108000.switch lan2: configuring for phy/internal link mode [ 47.268437] 8021q: adding VLAN 0 to HW filter on device lan2 [ 47.277164] br-lan: port 1(lan2) entered blocking state [ 47.281704] br-lan: port 1(lan2) entered disabled state [ 47.290452] device lan2 entered promiscuous mode [ 47.293784] device eth0 entered promiscuous mode [ 47.393640] gswip 1e108000.switch lan3: configuring for phy/rmii link mode [ 47.408776] 8021q: adding VLAN 0 to HW filter on device lan3 [ 47.416143] br-lan: port 2(lan3) entered blocking state [ 47.420165] br-lan: port 2(lan3) entered disabled state [ 47.437588] device lan3 entered promiscuous mode [ 47.482774] gswip 1e108000.switch lan4: configuring for phy/rmii link mode [ 47.488911] 8021q: adding VLAN 0 to HW filter on device lan4 [ 47.497737] br-lan: port 3(lan4) entered blocking state [ 47.501650] br-lan: port 3(lan4) entered disabled state [ 47.509690] device lan4 entered promiscuous mode [ 47.537127] gswip 1e108000.switch lan1: configuring for phy/internal link mode [ 47.543738] 8021q: adding VLAN 0 to HW filter on device lan1 [ 47.600880] EXT4-fs (sda1): recovery complete [ 47.608422] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: [ 47.676643] mount_root: switched to extroot [ 50.668846] gswip 1e108000.switch lan4: Link is Up - 100Mbps/Full - flow control rx/tx [ 50.683668] br-lan: port 3(lan4) entered blocking state [ 50.687605] br-lan: port 3(lan4) entered forwarding state [ 50.737519] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 52.179436] br-lan: port 4(wlan0) entered blocking state [ 52.183393] br-lan: port 4(wlan0) entered disabled state [ 52.189853] device wlan0 entered promiscuous mode [ 52.820840] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 52.826545] br-lan: port 4(wlan0) entered blocking state [ 52.831501] br-lan: port 4(wlan0) entered forwarding state hello BusyBox v1.35.0 (2023-04-27 20:28:15 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt 22.03.5, r20134-5f15225c1e ----------------------------------------------------- root@OpenWrt:/# cd //etc/modules-boot.d/* /bin/ash: cd: can't cd to //etc/modules-boot.d/02-crypto-hash: Not a directory root@OpenWrt:/#